Home » News » Products Knowledge » What is a bridged amplifier? Function of bridging of professional power amplifier

What is a bridged amplifier? Function of bridging of professional power amplifier

Views: 899     Author: Sanway Audio     Publish Time: 2020-08-22      Origin: Sanway Audio

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
What is a bridged amplifier? Function of bridging of professional power amplifier

Bridge mode is a connection method for power amplifiers in the professional audio field.

 

Most professional audio amplifiers support bridging. Switch the state of the amplifier to bridge mode (BTL), and then the speaker wiring is connected across the output stage (positive) of the two channels, and the speaker is not grounded. As for the phase positive and negative, the power amplifier will have the positive and negative poles of the BTL.

 

The bridge connection of the audio power amplifier is to push the output ends of the two amplifier circuits into a group of loads (speakers or speaker systems) at the same time.

 

When bridging, the audio waveforms output by the two amplifier circuits are inverted and loaded on the speaker at the same time, so that the load has twice the audio voltage, and the power is increased by four times (under the condition that the ideal current is sufficient, and the load impedance is the same .However, due to power limitation, the current cannot keep up, so the bridge is often not suitable for impedances below 8 ohms, so the output power is generally doubled)

 

Most professional performance, KTV and other power amplifiers support the bridge mode. After the power amplifier is adjusted to the bridge state, the speaker does not need to be grounded (the black negative terminal is empty), and the speaker wiring is connected across the two red output stages. The red terminal will indicate the phase of the bridge (that is, the positive and negative poles).

 

So, under what circumstances do you need to use the bridging function and how to bridge it? How to calculate the power after bridging and what harm will the use of the bridge do to the audio?

 

PART1 Why do we need to bridge?

 bridge mode

1. In the early power amplifier products, due to the limitation of component parameters, a single channel could not achieve high power output. Using the bridge mode can alleviate the desire for high power output;

 

2. When the single channel power of the power amplifier is not enough to drive high-power size speakers (such as dual 18-inch ultra-low speakers), the bridge mode needs to be used to meet the high-power requirements of the speakers;

 

3. In order to save costs, the higher the single-channel power amplifier, the more expensive the price, the use of bridge mode can meet the high-power output;

 

4. There is a certain distance between on-site wiring, a large number of speakers and a large power demand, and the environment is relatively special, the bridge mode will be used to promote multiple high-power speakers.

 

 

PART2 How to bridge the amplifier?

 bridge mode

 

1. Analog power amplifier

 

Generally, the input interface board is equipped with a code switch, and the switch is changed from studio (stereo) to bridge (bridged mono) behind the power amplifier

 

Connection method: connect the positive pole of the speaker to the positive pole of the left channel of the power amplifier, and connect the negative pole of the speaker to the positive pole of the right channel of the power amplifier. The volume is controlled by the gain knob of the left channel!

 

2. Digital power amplifier

 

Generally, the input terminal of the interface board has a bridge button; when using the bridge function, the bridge button needs to be in the ON state, but there is no bridge status indicator;

 

When using the bridge function, any port of the two output SPEAKON sockets is connected to 2+, 2-.

 

Tips:

Because the output power of the digital power amplifier is very large, in order to reduce the port contact resistance (reduce the heat), it is best to use the parallel connection method. OUT1 (1+, 2+) is connected to the speaker terminal 1+, OUT2 (1-, 2-) Connect 1- on the speaker end.

 D20K professional audio power amplifier


PART3 How to calculate the power after bridge?

 

Take a single channel with 8 ohm load power 200W as an example, at this time, each channel U=Ua=Ub=40V, after bridge Uab=Ua-Ub=40V-(-40V)=80V, when calculating the power P=U*U /R=80*80/8=800W, the same input signal, it can be seen that when the same impedance load is connected after the bridge, it is four times the power of the single channel.

 

However, in practical applications, due to the power problems provided by the internal power supply of the power amplifier, the line loss, the internal resistance of the power amplifier and other comprehensive factors, generally cannot achieve the ideal 4 times the power output. The digital power amplifier with better quality is 3.75 times and the analog power amplifier is full. The power is only about 2.5.

 

PART4 What is the bad influence on the speaker when set bridge mode?

 

1. The power amplifier bridge is often used for high-power low-voice speakers.

 

Theoretically speaking, it has an impact on the sound quality, but the human ear can't hear it. If you use a bridged amplifier to push the full range, the sound from the speaker will make people feel very refreshing. Just grasp it, usually it is It won't burn.

 

It is common to burn speakers in a disco. The main reason is that the power configuration is not good, or the pressure limit is not adjusted properly, and the DJ mixer level is at the end, the input level of the mixer is at the end, and the output power is at the end. If the level is less than -10dB, it will burn.

 

2. Choosing a power amplifier bridge to push large speakers is the next step in system applications, and it is a real trick. Theoretically, the power is doubled and it can be advanced.

 

However, users have overlooked a very important question. Theoretically speaking, the power amplifier bridging refers to the situation that the technical parameters of the two channels are completely the same, but it is completely impossible in practice. Even the top foreign power amplifiers are very It is difficult to make sure that the channel is at the mercy.

 

Therefore, it is improper when the bridge is connected because the power mismatch causes the horn to burn. The first thing is the crossover distortion caused by the bridge and the imbalance of the parameters of the two channels. Therefore, the improper bridge is the power mismatch. The main cause of the burning of the speaker is still the crossover distortion caused by the bridge and the imbalance of the parameters of the two channels.

 

Bridging is like having your legs and hands tied together. Once you use it, you must maintain the harmony of your actions, otherwise you will make mistakes.

 

3. The double "18" or double "15" or double "12" ultra-low sound is usually 4 ohms. As long as the function can be bridged under 4 ohms, there is no doubt about it, and it has nothing to do with the working method. The reason why the power amplifier is so powerful is that the internal circuit is bridged.

 

Ultra-low sound power Generally speaking, the power amplifier can be 3 times the extra power of the speaker.

 

There are many factors to burn the speakers, in addition to the hardware itself, it is usually caused by improper operation of the personnel.


CONTACT US

 : JinLe industrial Park, Pingbu Avenue, HuaDu District 510800, Guangzhou China
 : 
+86-20-3770-8242(Working time) 

      +86 13826042826
 : +86 13826042826
 : sanway.audio
 : sales@china-sanway.com

QUICK LINKS

YOUR MESSAGE

Copyright   2020 Sanway Professional Audio Equipment Co., Ltd All rights reserved.    Supported by Leadong